Output Power: 1W/500mW
Certification: CE-RED
Type: Analog Walkie Talkie
Size (mm):35.6*19
The SA528 is a cost-effective, highly integrated U/V dual-band professional walkie-talkie module. It integrates a high-speed microcontroller, a high-performance RF transceiver chip, and an RF power amplifier, delivering reliable and efficient wireless communication performance.The module provides a standard serial interface, enabling users to easily configure parameters and control transmit/receive functions. By simply connecting an external speaker to this module, it can function as a compact walkie-talkie. The Type-C interface and ultra-compact size enable a wide range of applications. With PC software for parameter configuration, it can easily communicate with off-the-shelf analog walkie-talkies on the market. It can be easily embedded into various portable and handheld devices, significantly enhancing overall system performance and integration efficiency.
The SA528 is manufactured and tested using lead-free processes and fully complies with RoHS and REACH environmental standards.
Parameter | Test condition | Min | Typ. | Max | Unit |
Power supply | 3.3 | 4.2 | 5 | V | |
Working Temperature range | -30 | 25 | 70 | ℃ | |
Current Consumption | |||||
Sleep current | ≤75 | uA | |||
RX current | 76 | mA | |||
TX current(High power) | @4.0V,1W | 700 | 800 | 900 | mA |
TX current(low power) | @4.0V,0.5W | 500 | 600 | 700 | mA |
Transmitting RF Parameters | |||||
Frequency range | UHF | 400 | 470 | MHz | |
VHF | 136 | 174 | MHz | ||
Out power(high power) | @VCC=4.0V | 29 | 30 | 31 | dBm |
Out power(low power) | 26 | 27 | 27.5 | dBm | |
Modulation frequency | @1.5KHz/2.5KHz frequency deviation | 10 | mV | ||
Audio modulation distortion | 2 | 5 | % | ||
Signal toNoise Ratio | 38 | 40 | 45 | dB | |
adjacent-channel power | @12.5K offset | -60 | dBc | ||
CTCSS Modulation frequency | 0.35 | 0.5 | 0.75 | KHz | |
Receiving RF Parameters | |||||
Receiving sensitivity | 13dB output voice signal ratio | -120 | -124 | dBm | |
Receiving SNR | @1.5KHzfrequency deviation | 45 | 50 | dB | |
Audio output amplitude | 700 | mV | |||
Audio Output impedance | 200 | Ohm | |||
Working voltage (V) | 150.75MHz | 416.75MHz | ||
Power(dBm) | Current(mA) | Power(dBm) | Current(mA) | |
3.3 | 28.2 | 620 | 26.9 | 624 |
3.6 | 29.4 | 691 | 28.7 | 808 |
4.0 | 30.1 | 777 | 29.8 | 901 |
4.5 | 30.9 | 913 | 30.8 | 984 |
5.0 | 31.5 | 1030 | 31.7 | 1070 |
UHF band frequency: 400~470 MHz
VHF band frequency: 136~174 MHz
( Note: The above frequency modules can simultaneously support)
Independent transmit and receive frequency
Band width 12.5KHz / 25 KHz
RSSI signal strength indicator
Distance up to 4-5km in open area
High Sensitivity:-124 dBm
Support wireless data transmission and reception
TCXO crystal, Stable performance
38 CTCSS
166 codes of normal/reverse CDCSS digital squelch
8 level squelch & 8 adjustable volume
High/ low power is optional (500mW/1W)
Wide range of working voltage:3.3-5V
Built in EEPROM, data saved in case of power failure
High integration, Ultra-compact size
Small walkie talkie
Invisible intercom system
Audio surveillance system
Outdoor Sport products
Building community security system



Pin NO. | Pin name | I/O | I/O Voltage | I/O state |
1 | MIC_IN | I | Microphone signal input. An external microphone requires an external bias resistor. | |
2,11,13,19 | GND | Grounding | ||
3 | TXD | O | 0-3.3V | Serial port for sending data |
4 | RXD | I | 0-3.3V | Serial port receiving data port (Note: in module sleep mode, the user device needs to output a low level to prevent leakage or poor reset) |
5 | 1 | I | 0-3.3V | Frequency 16-channel 8421 encoding, Bit 1, default "1" output. |
6 | 2 | I | 0-3.3V | Frequency 16-channel 8421 encoding, Bit 2, default "1" output. |
7 | 4 | I | 0-3.3V | Frequency 16-channel 8421 encoding, Bit 4, default "1" output. |
8 | 8 | I | 0-3.3V | Frequency 16-channel 8421 encoding, Bit 8, default "1" output. |
9 | VOXEN | I | 0-3.3V | Default: No function (This pin can be customized as "VOX enable pin". Note: The VOX version does not support data transmission) |
10 | SPKEN | O | 0-3.3V | Receive signal indicator. High in idle state; goes low when a signal is received. |
12 | ANT | RF input/output pin (connect to 50Ω antenna). | ||
14 | SPKP | O | Audio output pin. Connect to 8Ω / 2W speaker. | |
15 | SKPN | O | Audio output pin. Connect to 8Ω / 2W speaker. | |
16 | VOL- | O | SA518 module volume output pin. Internally connected to a potentiometer pin. The customer may leave this pin floating if no external volume potentiometer is needed. If an external volume potentiometer is required, the on-board potentiometer must be removed. | |
17 | VOL+ | I | Audio input pin for onboard power amplifier. Internally connected to a potentiometer pin. The customer may leave this pin floating if no external volume potentiometer is needed. If an external volume potentiometer is required, the on-board potentiometer must be removed. | |
18 | H/L | I | 0-3.3V | High/Low output power control; Leave open for high output power,low level to low output power. |
20 | PTT | I | 0-3.3V | Transmit/Receive control pin. Floating or pulling up is receive mode; pulling down is transmit mode. |
21 | CS | I | 0-3.3V | Module sleep control pin. High level = active (normal operation); low level = sleep. Default high (internal pull-up). |
22 | GND | Grounding | ||
23 | VCC | I | 0-5V | Connect power positive |

Privacy Policy
· Privacy Policy
There is currently no content available
Email:sales@nicerf.com
Tel:+86-755-23080616