Output Power : 1mW
Size (mm):13.5*22.2
UWB3000F33 is based on Qorvo's DW3000 UWB chip and features an integrated 2W high-power amplifier (PA). It complies with the IEEE 802.15.4-2020 standard and supports Two-Way Ranging (TWR) and Time Difference of Arrival (TDoA) positioning systems, delivering positioning accuracy of up to 10 cm.
Parameter | Condition | Min. | Typ. | Max. | Unit |
Supply Voltage | 3.0 | 5.0 | 5.5 | V | |
Operating Temperature Range | - 40 | 25 | 85 | ℃ | |
Frequency Range | CH5 | 6489.6 | MHz | ||
CH9 | 7987.2 | MHz | |||
RF Data Rate | 850k | 6.8M | bps | ||
Current Consumption | |||||
Sleep Mode | < 1.5 | uA | |||
Rx | 74 | mA | |||
Tx | CH5 | 850 | mA | ||
CH9 | 800 | mA | |||
TX current for range measurement | Peak Current | 850 | mA | ||
Average Current | 21 | mA | |||
Transmit parameters | |||||
Tx Power | @VCC=5V,CH5 | 31.5 | 33 | 34 | dBm |
@VCC=5V,CH9 | 26.5 | 28 | 29 | dBm | |
Adjustable Transmit Power Range | @VCC=5V,CH5 | 2 | 33 | dBm | |
@VCC=5V,CH9 | 0 | 29 | dBm | ||
Tx Bandwidth(BW) | 499.2 | MHz | |||
Receive parameters | |||||
Rx Sensitivity | @850Kbps | -100 | dBm | ||
@6.8Mbps | -94 | dBm | |||
IEEE802.15.4-2020 UWB
Supports channels 5 (6489.6 MHz) and Channel 9 (7987.2MHz)
Data rates of 850 kbps and 6.8 Mbps
Packet length up to 1023 bytes
Supports 2-way ranging, TDoA location
Programmable output power
Provides precision location and data transfer simultaneously
Asset location to an accuracy of 10 cm
Long distance communication and ranging
Precision real time location systems (RTLS) using two-way ranging, TDoA schemes in a variety of markets: Healthcare\ Consumer\ Industrial\ Automotive
Location aware wireless sensor networks
Presence detection for secure entry and secure payment


Pin No. | Pin definition | I/O | Level | Description |
1 | VCC | VCC (3.0-5.5V) | ||
2,12,13, 15,16,18 | GND | Ground | ||
3 | WAKEUP | DI | 0-3.3v | When asserted into its active high state, the WAKEUP pin brings the DW3000 out of SLEEP or DEEPSLEEP states into operational mode. This should be connected to ground if not used. |
4 | NRSTn | DIO | 0-3.3v | Reset pin. Active Low Output. May be pulled low by external open drain driver to reset the DW3000. Must not be pulled high by external source. |
5 | CLK | DI | 0-3.3v | SPI peripheral clock input. |
6 | MOSI | DI | 0-3.3v | SPI peripheral data input. |
7 | MISO | DO | 0-3.3v | SPI peripheral data output. |
8 | CSN | DI | 0-3.3v | SPI chip select. This is an active low enable input. The high-to-low transition on SPICSn signals the start of a new SPI transaction. SPICSn can also act as a wake-up signal to bring DW3000 out of either SLEEP or DEEPSLEEP states. |
9 | IRQ | DI | 0-3.3v | Interrupt request output from the DW3000 to the host processor. By default IRQ is an active-high output but may be configured to be active low if required. For correct operation in SLEEP and DEEPSLEEP modes it should be configured for active high operation. This pin will float in SLEEP and DEEPSLEEP states and may cause spurious interrupts on the host unless pulled low externally (100kΩ recommended). When the IRQ functionality is not being used the pin may be reconfigured as a general purpose I/O line2 , GPIO8. |
10 | GPIO4 | DIO | 0-3.3v | GPIO4 from DW3000. |
11 | NC | |||
14 | RXANT | RF Input, Connect to an External 50 Ω Antenna | ||
17 | TXANT | RF Output, Connect to an External 50 Ω Antenna |

Privacy Policy
· Privacy Policy
There is currently no content available
Email:sales@nicerf.com
Tel:+86-755-23080616